Brand: XPRO®
Brand: XPRO®
Palm and back goatskin leather, straight thumb with reinforcement, ANSI A6 cut resistance, para‑aramid lining, extended cow split leather cuff.
EN 388 2016 Results: 3X33F
Abrasion: 3
Cut (Coupe Test): X
Tear: 3
Puncture: 3
Cut (TDM-100 Test): F
EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove’s ratings.
Abrasion Level: 3
Test Method: ASTM D3389-10
The ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves, and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicate greater abrasion resistance of the product and a higher Abrasion Level.
Cut Level: A6
New edition ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9.
Puncture Level: 3
The ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.
The EN ISO 21420:2020 standard outlines the general requirements and test methods for protective gloves. It covers aspects such as design, construction, comfort, efficiency, and safety, ensuring gloves meet necessary performance criteria. This standard applies to all protective gloves, including those used in industrial environments, and replaces the previous EN 420:2003 standard.
The CE mark (Conformité Européenne) indicates that a safety product meets the essential health, safety, and environmental protection requirements of the European Economic Area (EEA). It ensures that the product complies with relevant EU directives and can be sold freely within the EEA, providing assurance of its safety and quality.
Category II (Cat II) gloves are designed for intermediate risks, meaning they provide protection against mechanical, thermal, or chemical hazards but are not intended for extreme dangers. These gloves must be tested and type-approved by an EU-recognized institute and labeled with pictograms indicating their protective functions.
EN 388 2016 Results: 3X33F
Abrasion: 3
Cut (Coupe Test): X
Tear: 3
Puncture: 3
Cut (TDM-100 Test): F
EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove’s ratings.
Abrasion Level: 3
Test Method: ASTM D3389-10
The ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 is used for uncoated gloves, and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicate greater abrasion resistance of the product and a higher Abrasion Level.
Cut Level: A6
New edition ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9.
Puncture Level: 3
The ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.
The EN ISO 21420:2020 standard outlines the general requirements and test methods for protective gloves. It covers aspects such as design, construction, comfort, efficiency, and safety, ensuring gloves meet necessary performance criteria. This standard applies to all protective gloves, including those used in industrial environments, and replaces the previous EN 420:2003 standard.
The CE mark (Conformité Européenne) indicates that a safety product meets the essential health, safety, and environmental protection requirements of the European Economic Area (EEA). It ensures that the product complies with relevant EU directives and can be sold freely within the EEA, providing assurance of its safety and quality.
Category II (Cat II) gloves are designed for intermediate risks, meaning they provide protection against mechanical, thermal, or chemical hazards but are not intended for extreme dangers. These gloves must be tested and type-approved by an EU-recognized institute and labeled with pictograms indicating their protective functions.
Applications: Welding Gloves, Metal Handling Gloves, Heavy‑Duty Industrial Gloves, Construction Gloves
Trades:Welding, Metal Fabrication, Construction, Manufacturing
Hazards: Cut Hazards, Heat, Abrasion, Sharp Edges
Industries: Oil & Gas, Metal Fabrication, Construction, Heavy Manufacturing, Welding
Plot 416, 431 Sector 7/a Korangi Industrial Area, Karachi, Sindh 74900
All content, including text, graphics, logos, and designs, is the exclusive property of XPRO®. It is protected under patent, copyright, and trademark laws. Unauthorized use, reproduction, or distribution is strictly prohibited. All rights reserved.
